Loading Dock Structures, Dock Levellers, Docks Doors, Australia



Send to Friend
You are here :

Home

>

docks-doors

>

Dock-levellers

>

Loading Dock Structures

Loading Dock Structures

Loading Dock Structures

Product Code : LDST

Stand-alone solution for housing an LDL20 Automatic Hydraulic Loading Dock Leveller
Can be fitted with Dock Shelters & Sectional Doors
No major modifications to existing structures
Customisable to suit new & existing buildings
 

 

Page 1 2 3 4 5
Enlarge
Application

Leda's Loading Dock Structure is a loading system that represents a complete and stand-alone unit that is installed in front of the building.
It can be fitted with all components of a docking system: a dock leveller, a dock shelter and an overhead sectional door.
(refer individual product pages)

Since it is installed outside the building directly in front of the door opening, it has great advantages over a conventional internal ramp for both new buildings as well as for existing buildings that are to be upgraded - without any major modifications to the construction of the building.
As a standard the entire steel frame construction of the Leda's Loading Dock Structure is hot dip galvanised.
Recommended options are a roof drainage system and flashing, adapted to your building.

Advantages
Thermal separation of warehouse and docking system guarantees considerable energy saving, important for temperature controlled and freezer warehouses.

Easy and fast installation of pre-assembled components on existing foundations which can be fastened on the outside wall of the building, without disrupting the daily use of the building.

The cladding consists either of non-insulated profile sheet material or of 40 mm insulation panels; it can also be cladded with the material of the warehouse facade.

The Loading Dock Structure design allows the use of a dock leveller and the installation of a mechanical or inflatable dock shelter, whatever best suits the loading frequency.

Because of individual components it can be installed as a single house or a multiple system either at a normal 90deg orat a 45deg or 145deg angle if the room in front of the loading system is limited.

The storage room in the warehouse is extended since the complete docking system is placed outside the building.

Customised Options

Contact Leda for further information.


Dimensions
NW - Nominal width [3300, 3500, 3600 mm]
NL - Nominal length
TH - Total height
DH - Dock height
NH - Nominal height dock shelter
NT - Nominal width dock shelter
MH - Assembly height dock shelter

Recommendation: MH=4500 for truck-heights upto 4000 mm
Note: Mechanical Loading Dock Shelter shown - Air Inflated Dock Shelter may change some dimensions.



* Measurement only valid for insulated wall setup.

Features

Sizes - nominal length* 2000, 2450, 3000 mm
Sizes - nominal width* 3300, 3500, 3600 mm
* Other sizes are available on request
Thickness of insulation cladding:
Roof and wall panels with 40 mm insulation (optional)
Surface treatment:
Hot dip galvanised
Inside colour-coated (optional)
Outside colour coated 25 μm (optional)
Thickness ofUninsulated cladding:
0,63 mm profiled steel sheet
Surface treatment:
Hot dip galvanised
Inside protective coating 10 μm (optional)
Outside colour-coating 25 μm (optional)
Surface steel frame:
Hot dip galvanised




Parts Overview
1 - Steel cladding
2 - Dock leveller (not included)
3 - Dock shelter(not included)
4 - Dock support structure
5 - Overhead sectional door(not included)
Drain pipe and gutter

To have controlled water drainage, the load house can be equipped with drain pipe and gutter.
Anti-drip-coating

To avoid condense water leading to moisture in the loading area, the inside surface of the roof sheet material can be delivered with a layer of felt as anti-drip-coating.
Wall connection profile

To connect the load house structure to the building, lateral and horizontal angle profiles including sealing material can be included in the installation.
Wall protection plywood veneer

To protect the walls inside the load house against possible damage from the handling equipment, the lower part can be equipped with a cover of a plywood veneer (1200 mm high).
This is also the recommended solution for applications where the inside walls needs to be closed and have a straight surface.

Further Options

Please contact Leda for further information.

No files to download
No videos for this product.

Leda Security, Sydney, Melbourne, Brisbane, Adelaide, Perth, Australia

Sydney Web Design Business
|
Sydney Website Builder
|
Webdesigner
|
Seo Services Company
|
Marketing Search Engine

25th May 2013